Address: Room 100, No.37-1 Sanjianzai Street, Minzhu Community, Shajing Street, Bao ‘an District, Shenzhen
Phone: 0755-29032264
Mob: 18664575008
MR‘Zhou QQ:190461522
Skype:ouyang
| The first part of comprehensive ability | ||||
| classification | serial number | project | Project parameters | |
| General ability | The limit capacity | |||
| Inspection standard | 1 | Acceptance criteria | PCB total standard GB/T 16261-1996, | IPC-6012 Class Ⅲ |
| IPC-6012 Class Ⅱ | ||||
| 2 | Acceptance criteria | Total military PCB specification GJB362-96, | ||
| IPC-6012 Class Ⅲ | ||||
| 3 | Test method for | IPC-TM-650,GB/T4677-2002 | ||
| Engineering software | 1 | Design software | TANGO，PROTEL系列，PADS2000， | |
| Powerpcb系列，AUTOCAD | ||||
| 2 | Light painting file format | Light painting file (GERBER file) and the corresponding drilling file, | ||
| 3 | Drilling file format | EXCELLON format bitmap (hole) | ||
| Layer/thickness | 1 | The layer number | 2-26 floors | 30floors |
| 2 | thickness | 0.3 -- 4.0 mm (5.0 mm) largest plate thickness | 0.2-0.3mm； | |
| 4.0-5.0mm | ||||
| 3 | Double panel thickness | 0.4 -4.0mm | The biggest 5.0 MM | |
| A minimum of0.3mm | ||||
| 4 | Four layer board thickness | 0.6mm-4.0mm | The biggest 5.0 mm | |
| A minimum of0.45mm | ||||
| 5 | 6 layer board minimum thickness | 0.8mm—4.0 | The biggest 5.0 mm | |
| A minimum of 0.65mm | ||||
| 6 | Minimum eight layer plate thickness | 1.2mm---4.0 | The biggest 5.0 mm | |
| A minimum of 1mm | ||||
| 7 | Ten layer board minimum thickness | 1.5mm---4.0 | The biggest 5.0 mm | |
| A minimum of 1.2mm | ||||
| 8 | Ten floor plate minimum thickness | 1.6m---4.0 | The biggest 5.0 mm | |
| A minimum of 1.4mm | ||||
| 9 | 14 layer board minimum thickness | 1.8mm----4.0 | The biggest 5.0 mm | |
| A minimum of 1.65mm | ||||
| Sheet/piece | 1 | The commonly used copper clad specifications | 0.13 1/1， 0.13 H/H，0.21 1/1，0.25 1/1 ,0.36 1/1，0.51 1/1，0.71 1/1，1.0 1/1，1.2 1/1,1.6 H/H，1.6 1/1，1.6 2/2，2.0 1/1，2.0 2/2，2.5 1/1，3.0 1/1，3.2 1/1 | 0.05 H/H |
| 阴阳铜：18/35 35/70 70/105 | ||||
| 2 | Commonly used half curing specifications | 7628（0.185mm），2116（0.105mm）， | SPEED BRORD C;6700; 49N | |
| 1080（0.075mm）， 3313（0.095mm）， | ||||
| RO4403（4mil），RO4350(4mil) | ||||
| 3 | Rogers plate type | Ro4350,Ro4350B,Ro4003,Ro4003C | Other materials need to review | |
| 4 | Arlon plate type | AD350,AR1000,25FR,33N,Diclad527 | ||
| TACONIC plank | RF35 | |||
| 5 | Tg halogen free plate type (normal) | Born good S1155, semi solidified S0155 | ||
| 6 | Halogen free plate type (high Tg) | Born good S1165, semi solidified S0615 | ||
| 7 | High Tg board type | Born good S1141 170, half piece S0401 curing | ||
| Born good S1170, semi solidified S070 | ||||
| size: | 1 | Maximum size finished product delivery | 20×24 inch | 22×42inch (review) |
| 2 | Minimum size of finished product delivery | 2cm*3cm | ||
| 3 | High frequency board biggest puzzle size | 16×18 inch | ||
| The surface of the | 1 | Surface treatment | Tin with lead, lead-free tin, zedoary, sink, sink, OSP, plated gold and silver carbon oil;Zedoary + tin with lead;Zedoary + lead-free tin | |
| process | 2 | Gold finger length surface treatment | Water, plated gold | |
| Resistance against | 1 | Impedance control panel board type | FR - 4 series, series of Rogers, Arlon series, Taconic series | |
| 2 | Impedance model | Difference, single side | ||
| 3 | Impedance tolerance | ±10% | ±5%(review) | |
| The ability to process it | 1 | BGA solder minimum diameter | 10 mil (refers to the bonding pad without hole, heavy silver or gold, OSP, sink sink tin 8 mil) | 8 mil (means no hole welding plate, heavy silver or gold, OSP, sink sink tin 6 mil) |
| 2 | Thickness tolerance (1.0 mm) or less | ±0.1 | / | |
| 3 | Thickness tolerance (> 1.0 mm) | Plus or minus 10% (< 1.0 mm thickness of 2.4 mm or less); | (0.10 mm thickness of 2.0 or less);(0.15 mm thickness of 2.0-3.0);(0.2 mm thickness of 3.0 or higher) (there is no specified laminated these refers to the customer request) | |
| Plus or minus 8% (2.4 mm) thickness > | ||||
| 4 | Inner most complete copper thick (OZ) | 3 OZ | 4-5 OZ（(review) | |
| 5 | Outer biggest finished copper thickness (OZ) | 4 OZ | 6 OZ（(review) | |
| 6 | Thickness aperture ratio | 8:1 (minimum aperture 0.20 mm) | Whoever (the smallest aperture 0.25 mm) | |
| 7 | Warp degrees | 0.7% (conventional);0.5% (SMT) | Limit of 0.2% | |
| 8 | Shape way | CNC, V - CUT, bridging + stamp holes | / | |
| 9 | Blind hole process | CNC, V - CUT, bridging + stamp holes | The cross blind hole, laminated number 6 | |
| 10 | Insulating layer thickness (minimum) | CNC, V - CUT, bridging + stamp holes | 0.06MM | |
| 11 | Minimum of hole wall copper thickness | 20—25um | 25-45 | |
| 12 | The inner processing | black | / | |
| The second part of the process production capacity | ||||
| process | The serial number | project | Project parameters | |
| General ability | The limit capacity | |||
| Light painting room | 1 | Light painting machine biggest film size | 22×28 inch | 36×48 inch（outgoing) |
| 2 | Red field exposure | 28×35 inch | / | |
| 3 | Red piece of developing machine maximum size | Unilateral no greater than 19.7 inch | / | |
| 6 | Light painting minimum line width/span | 4/4mil | 3/3mil | |
| 8 | Red piece minimum line width/span | 4/4mil | 3/3mil | |
| Before light imaging processor | 1 | thickness | 0.36 -- 5 mm (chemical cleaning section: 0.05-5) | 0.05-5.0MM |
| 2 | The minimum dimension | 5×6 inch | / | |
| 3 | The largest processing size | Less than 24 inch shorter side | / | |
| sticker | 1 | thickness | 0.05—3.0mm | 0.05-5.0MM |
| 2 | The largest processing size | The side of the short 24 inch | / | |
| Minimum line width spacing | 2 | The inner minimum line width | 4 mil | 3 mil |
| （1/2OZ copper compensation before） | ||||
| 3 | The inner minimum line width | 5mil | 4mil | |
| （1OZ copper compensation before） | ||||
| 4 | The inner minimum line width | 8 mil | 6 mil | |
| （2OZ copper compensation before） | ||||
| 5 | The inner minimum line width | 12 mil | 10 mil | |
| （3OZ copper compensation before） | ||||
| 6 | The inner minimum line width | 18 mil | 14mil | |
| （4OZ copper compensation before） | ||||
| 7 | The inner minimum line spacing | 3.5 mil | 3 mil | |
| （1/2OZ copper after compensation） | ||||
| 8 | The inner minimum line spacing | 4 mil | 3.5mil | |
| （1OZ copper after compensation） | ||||
| 9 | The inner minimum line spacing | 6mil | 5mil | |
| （2OZ copper after compensation） | ||||
| 10 | The inner minimum line spacing | 7 mil | 6 mil | |
| （3OZ copper after compensation） | ||||
| 11 | The inner minimum line spacing | 8 mil | 7 mil | |
| （4OZ copper after compensation） | ||||
| 12 | The outer minimum line width | 4 mil | 3 mil | |
| （1/2OZ copper compensation before） | ||||
| 13 | The outer minimum line width | 5 mil | 4mil | |
| （1OZ copper compensation before） | ||||
| 14 | The outer minimum line width | 9mil | 8mil | |
| （2OZ copper compensation before） | ||||
| 15 | The outer minimum line width | 12mil | 10mil | |
| （3OZ copper compensation before） | ||||
| 16 | The outer minimum line width | 18mil | 15mil | |
| （4OZ copper compensation before） | ||||
| 17 | The outer minimum distance | 3.5 mil | 3.2 mil | |
| （1/2OZ after compensation） | ||||
| 18 | The outer minimum distance | 3.5 mil | 3.2 mil | |
| （1OZ after compensation） | ||||
| 19 | The outer minimum distance | 5 mil | 4 mil | |
| （2OZ after compensation） | ||||
| 20 | The outer minimum distance | 8 mil | 6 mil | |
| （3OZ after compensation） | ||||
| 21 | The outer minimum distance | 12 mil | 8 mil | |
| （4OZ after compensation） | ||||
| 22 | Biggest exposure machine | 22×28 inch | / | |
| Maternal size (inner) ASA | ||||
| 23 | The biggest exposure machine production | 22×28 inch | / | |
| The size (outer) ORC | ||||
| 25 | The size (outer) ORC | 10 mil (6) or less;12 mil (7-14 layer);The 14th floor above 14 mil or higher | 8 mil (6) or less; | |
| The inner spacer ring width | 10 mil (7-14 layer) | |||
| The 14th floor above 12 mil or higher | ||||
| 26 | The inner pad unilateral is minimal | 5mil（18、35um），6mil（70um）， | 4mil（18、35um）， | |
| 8mil（105um） | 5mil（70um）， | |||
| 7mil（105um） | ||||
| 27 | The inner isolation bandwidth | 8 mil | 7 mil | |
| Minimum (compensation) | ||||
| 28 | The inner edge | 8 mil | 7 mil | |
| The minimum distance of copper | ||||
| 29 | The outer conductive graphics to | 8 mil | 6mil | |
| Appearance and minimum distance | ||||
| 30 | Grid line width/line | 6/6mil（1/2OZcopper）；6/6mil(1OZcopper）； | 5/5mil（1/2OZcopper） | |
| From the smallest (figure plating products) | 10/8mil（2OZcopper）；10/10mil（3OZcopper）； | |||
| 12/12mil（4OZcopper）。 | ||||
| 31 | Via bonding pad unilateral | 4mil | 3mil | |
| Minimum width | ||||
| 32 | Etching mark minimum line width | 8mil（18um）； | 6mil（18um）； | |
| 10mil（35um）； | 8mil（35um）； | |||
| 12mil（70um） | 10mil（70um） | |||
| AOI | 1 | The biggest dimensions ((SK-75) | 23.5×26 inch | / |
| 2 | The biggest dimensions ((868) | 23.5×26 inch | / | |
| 3 | thickness | 0.05--5.0 mm | / | |
| the | 1 | thickness | 0.05－2.40 mm | 0.05－4.5 mm |
| 2 | The biggest dimensions ( | Biggest 24 inch long side | / | |
| 3 | The minimum dimension | 6×6 inch | / | |
| laminated | 1 | Blind hole buried orifice plate is the most | 3 次 | 6次 |
| More pressing | ||||
| 2 | The thickness of the copper foil | 18um，35um，70um | ||
| 5 | Material mixed pressure | Rogers/ Arlon与FR-4 | ROGERS + buried capacitor (other type | |
| No need to review) | ||||
| 6 | thickness | 0.4—3.5mm | The biggest 5.0 mm | |
| 8 | Interlayer pressure medium | 0.075mm（18umcopper） | 0.06MM | |
| The minimum thickness | ||||
| 9 | Laminated slice selection | 1, interlayer sheet laminated thickness for the inner layer between copper and + 0.07 MM thick | ||
| 2, for using the laminated plate, near the plate laminated single lamination is not permitted. | ||||
| 10 | The biggest dimensions ( | 22×26inch | / | |
| Inch (vacuum pressure machine) | ||||
| 11 | Minimum of is between the layers | 4 mil | 3 mil | |
| 钻孔 | 1 | Cutter diameter | 0.2mm-6.3mm | 0.15 |
| Interval (0.05 mm), | ||||
| 2 | High-frequency plate minimum drilling | 0.25mm | 0.20mm | |
| 3 | A drill non-metallic smallest hole | 0.5mm | 0.2 | |
| 4 | The biggest diameter of thickness ratio | 10:01 | 12:01 | |
| 5 | The biggest dimensions ( | Two machine: 20 x 24 inch | 20×48 inch | |
| Six head machine: 20 x 24 inch | ||||
| 6 | Drilling to the minimum distance | 8 mil (6 layer board or less) | 5 mil (6 layer board or less); | |
| 10 mil (14 layer board or less) | 8 mil (14 layer board or less) | |||
| 7 | Drilling to the conductors | 9 mil (a pressing); | 7 mil (a pressing); | |
| Small distance (buried blind hole) | 10 mil (two or three times pressing) | 9 mil (two or three times pressing) | ||
| 8 | The same network hole wall | 6mil | 5mil | |
| Minimum spacing (compensation) | ||||
| 9 | Different network hole | 12 mil | 8 mil | |
| Wall of the minimum distance | ||||
| (compensation) | ||||
| 10 | The distance between the hole wall, not of metal | 8 mil | 6 mil | |
| 11 | (with hole location accuracy | ±3 mil | ±2 mil | |
| CAD data than) | ||||
| 12 | The plug-in aperture tolerance | ±6MIL | ±4mil | |
| (normal metal finished hole) | ||||
| 14 | The hole diameter tolerances | 0.04mm | 0.025mm | |
| 15 | Slot aperture male | ±0.15mm（long) | ±0.10mm（long) | |
| Poor (drill slot) | ±0.10mm（short） | ±0.075mm（short） | ||
| 16 | Slot cutter diameter | 0.60--1.20mm | 0.45mm | |
| 17 | Slots aspect ratio | 1.8：1 | / | |
| （Ladder, taper | ||||
| 18 | The depth of the hole tolerance | ±0.2mm | ±0.10mm | |
| Ladder, taper hole | ||||
| 19 | Mouth diameter tolerance | ±0.15mm | ±0.10mm | |
| Mouth diameter tolerance | ||||
| 20 | Ladder, cone hole Angle | 82、90degrees | To review the other Angle | |
| 21 | Ladder, taper hole | ±10degrees | / | |
| Angle tolerance | ||||
| Deburring machine | 1 | The minimum dimension | 8×8inch | / |
| 2 | The largest processing size | Less than 24 inch shorter side | / | |
| 3 | thickness | 0.8--5.0mm | 0.25--5.0 | |
| Heavy copper | 1 | Thickness aperture ratio (maximum) | Now (minimum aperture 0.20 mm) | 12：1（minimum aperture 0.20 mm） |
| 2 | The hole (hole) | 0.20 mm | 0.15mm | |
| 3 | The largest processing size | 24×33 inch | / | |
| Graphics electroplating | 1 | The outer finished copper thickness | 25—45 um | / |
| （1/3OZ copper） | ||||
| 2 | The outer finished copper thickness | 33—55 um | / | |
| （1/2OZ copper） | ||||
| 3 | The outer finished copper thickness | 46--70 um | / | |
| （1OZ copper） | ||||
| 4 | The outer finished copper thickness | 76--105 um | / | |
| （2OZ copper ） | ||||
| 5 | The outer finished copper thickness | 107--140 um | / | |
| （3OZ copper） | ||||
| 6 | The outer finished copper thickness | 137--180 um | / | |
| （4OZ copper） | ||||
| 7 | thickness | 0.2--4.8mm | 20.2-5.0 | |
| 8 | Dry film hole diameter | 3.6mm（older unilateral 8 | 4.5mm | |
| 9 | The minimum grid line width | 6/6mil（18um copper）； | 5/5mil（18um copper） | |
| / line spacing (plating, finished products) | 6/6mil（35um copper）；8/10（70um copper） | |||
| 10 | The largest processing size | 24×76inch | / | |
| 11 | Minimum spacing after compensation | 3.5mil | 3mil | |
| 12 | Thickness aperture ratio (maximum) | 10:1（(minimum borehole diameter 0.20) | 12：1(minimum borehole diameter 0.20) | |
| Resistance welding | 1 | The largest processing size | 26Inch | 40INCH |
| 3 | Resistance weld hardness | 6H | / | |
| 4 | The unilateral resistance welding | 2.5mil | 2MIL | |
| Small window (compensation) | ||||
| 5 | The resistance welding cover line | 2.5（局(local allow 2 mil | 2 | |
| Small single width | ||||
| 6 | Resistance welding open the window | 8mil | 6mil | |
| Operator minimum width | ||||
| 7 | Nonmetallic mineralization Kong Zu | 4mil | 3.5mil | |
| Welding unilateral least open a window | ||||
| 8 | Block points than drilling | 6mil | 4mil | |
| Large diameter of the smallest | ||||
| 9 | Resistance welding bridge minimum width | 4 mil (green), 5 mil (other color) | 3.5 mil (green), 4 mil (other color) | |
| 10 | Resistance welding color | Green, yellow, black, blue, white, red | Other models need to review | |
| 11 | Halogen free ink model | Green (NANYA LP - 4-91 - G/G) | / | |
| 12 | Resistance welding thickness ( | 10UM | 15UM | |
| Minimum line corner | ||||
| 13 | A hole cover oil thickness | 8-10um | 15UM | |
| 14 | Complete the biggest resistance welding | 1OZ—3OZ | 6OZ | |
| Copper thick (finished) | ||||
| 15 | Developing machining of thickness | 0.4--5.0mm | 0.2MM | |
| 16 | Developing machine minimum dimensions | 7×7inch | 5×5inch | |
| 17 | Developing machine processing biggest size | The side of a short 20 inch | Maximum 24 inch short edge; | |
| 18 | Plug hole diameter of the aperture (finished product) | ≤0.35mm | 0.4-0.8mm | |
| character | 1 | Processing the largest size | A printing biggest direction 30 inch long, | 40INCH |
| 2 | Character is the ink color | White, yellow, black, grey | ||
| 3 | Character to complete the biggest finished copper thickness | 5 oz (characters across the base material and the surface of the copper) | 6OZ(characters across the base material and the surface of the copper) | |
| 4 | Minimum line width, and characters | Word wide：4mil；High:：27mil | Word wide：4mil；High:：25mil | |
| Height (18 um copper) | ||||
| 5 | Minimum line width characters | Word wide：5mil；High:：30mil | Word wide：5mil；High:：28mil | |
| And height (35 um copper) | ||||
| 6 | Minimum line width characters | Word wide：6mil；High:：45mil | Word wide：6mil；High:：42mil | |
| And height (70 um copper) | ||||
| 7 | Characters and welding plate minimum distance | 6mil | 4MIL | |
| 8 | Minimum spacing between carbon oil | 15mil | 12mil | |
| 9 | Carbon and other oil | 10mil | 8mil | |
| Minimum spacing between conductors | ||||
| 10 | Carbon oil unilateral line (minimum) | 6mil | 4mil | |
| 13 | Carbon oil resistance | 15ohms | Other to review | |
| 14 | Blue glue type (type) | Blue green strippable plastic (SD - 2955) | / | |
| Blue has lead to rubber strip (SD - 2954) | ||||
| 15 | Blue glue thickness | 0.20--0.50mm | / | |
| 16 | Blue rubber cover line or welding | 7mil | 6MIL | |
| Plate of unilateral minimum | ||||
| 17 | Blue glue and welding plate minimum distance | 16 mil | 14 mil | |
| 18 | Blue glue white mesh plug hole diameter | 2mm | 3mm | |
| 19 | Blue glue plug hole diameter of the aluminum foils | 5mm | 6mm | |
| Gold finger | 1 | Nickel thickness | 3-5um | / |
| 2 | Gold | 0.8-1.3um | / | |
| 3 | The maximum length fingers | 2inch | / | |
| 4 | Between the gold finger | 7mil | 5 mil | |
| Small spacing (finished) | ||||
| zedoary | 1 | Nickel thickness | 3—8um | / |
| 2 | Gold | 0.05--0.75um | 0.05—1.0UM | |
| 3 | The surface technology of the mixed with zedoary | Carbon oil, tin, OSP, gold finger with lead (lead) | / | |
| Heavy tin | 1 | Tin thickness | 0.80-1.20um | / |
| 2 | The surface of the mixed with heavy tin process | Carbon oil, gold finger (lead) | / | |
| Heavy silver | 1 | Silver thick | 0.10-0.30um | / |
| 2 | he mixed with heavy silver surface process | Carbon oil, gold finger (lead) | / | |
| OSP | 1 | Film thickness | 0.15-0.30um | / |
| 2 | The surface of the mixed with OSP process | Carbon oil, gold finger (lead) | / | |
| Tin with lead | 1 | Minimum SMT/BGA | 6mil | / |
| Bonding pad spacing | ||||
| 2 | Spray tin before and after treatment | The side of the short 24 inch | / | |
| The largest processing size | ||||
| 3 | Spray tin before and after treatment | 7×7inch | / | |
| The minimum dimension | ||||
| 4 | Spray tin before and after treatment | 0.6—3.0mm | 0.5-4.0mm | |
| Thickness (finished) | ||||
| 5 | Tin thickness with lead (finished) | 0.6—3.0mm | 0.5-4.0mm | |
| 6 | Tin processing biggest size | 22×25inch | 22 x 42 inch (twice) | |
| 7 | Spray tin minimum dimension | 6×8inch | / | |
| 8 | Tin thickness | 2－40um | / | |
| 10 | With the tin with lead | Carbon oil, gold finger (lead) | Gold finger (leadless) | |
| The surface of the hybrid process | ||||
| 11 | Bare plate spray tin graphics minimum distance | 8mil | 7mil | |
| 12 | 金属化板边和金属化槽包金属焊环最小宽degrees | 30mil | 20mil | |
| Lead-free tin | 1 | Minimum SMT/BGA solder spacing | 7mil | 6mil |
| 2 | Tin thickness | 2－40um | / | |
| 3 | With lead-free tin | Carbon oil, gold finger (lead) | Gold finger (leadless) | |
| The surface of the hybrid process | ||||
| 4 | Metal plate edge and metallization slot metal welding ring minimum width | 30mil | 25mil | |
| 外形 | 1 | Contour machining size | 21×24inch | 21×40inch |
| 3 | Shape dimension precision (edge to edge) | ±6mil | ±4mil | |
| 4 | Minimum milling cutter diameter | 0.8mm | / | |
| 5 | Inside the minimum radius | 0.5mm | 0.4mm | |
| 6 | Contour milling cutter diameter | 0.80mm、1.0mm、1.20mm、 | / | |
| 1.60mm、2.00mm、2.40mm | ||||
| 7 | Goldfinger chamfer Angle | 20---60degrees | / | |
| 8 | Goldfinger chamfer Angle tolerance | ±5degrees | / | |
| 9 | Goldfinger chamfering depth tolerances | ±0.20 | / | |
| 10 | The slot aperture tolerance (groove) | ±0.15mm | ±0.12mm | |
| 11 | Ladder hole, groove depth tolerances | ±0.15mm | ±0.10mm | |
| 12 | Ladder hole and slot | ±0.15mm | / | |
| Mouth diameter tolerance | ||||
| 13 | 2 the hole size tolerance | Poor 3 or higher (for example, plus or minus 2 mil, + 3/0 mil, etc.) | Poor 2 mil or higher | |
| 14 | Two drilling accuracy (with CAD data than) | ±5mil | ±3mil | |
| 15 | thickness | 0.3－2.5mm | / | |
| 16 | The largest processing size | 20×24inch | / | |
| 17 | The minimum dimension | 6×6inch | / | |
| 18 | V - CUT Angle specifications | 20、30、45、60degrees | / | |
| 19 | V - CUT Angle tolerance | ±5° | / | |
| 20 | V - CUT the degree of symmetry tolerance | ±0.05mm | / | |
| 21 | V - CUT steel thickness | ±0.1mm | / | |
| More than (thick) tolerance | ||||
| 22 | V - CUT not the center of the copper | 0.3（20degrees），0.33（30degrees）， | / | |
| Minimum distance line to the graphics | 0.37（45degrees），0.42（60degrees） | |||
| (thickness 1.0 mm or less) | ||||
| 23 | V - CUT not the center of the copper | 0.36（20degrees），0.4（30degrees）， | / | |
| Minimum distance line to the graphics | 0.5（45degrees），0.6（60degrees） | |||
| (thickness 1.0 1.6 mm) | ||||
| 24 | V - CUT not the center of the copper | 0.42（20degrees），0.51（30degrees）， | / | |
| Minimum distance line to the graphics | 0.64（45degrees），0.8（60degrees） | |||
| (1.6 -- 2.4 mm thickness) | ||||
| 25 | V - CUT not the center of the copper | 0.47（20degrees），0.59（30degrees）， | / | |
| Minimum distance line to the graphics | 0.77（45degrees），0.97（60degrees） | |||
| (2.5 -- 3.2 mm thickness) | ||||
| 26 | Goldfinger chamfer Angle tolerance | ±5degrees | / | |
| 27 | Goldfinger chamfering thickness tolerance | ±5 mil | / | |
| 28 | Goldfinger lead width | 20 mil | 10MIL | |
| 29 | Gold finger with tin | 1mm | 0.8mm | |
| Cover resistance welding between the minimum spacing | ||||
| 30 | Not hurt by the gold finger | 7mm | 1MM | |
| The minimum distance from the TAB | ||||
| 32 | Bridge + stamp hole of conventional design | Each stamp hole three bridge, steel 0.3 mm wide, number 4, | / | |
| Aperture 0.6 1.0 mm bridge span 3 inch or less | ||||
| Electrical measuring | 1 | Test points away from the edge minimum distance | 0.5mm | / |
| 2 | The test on resistance | 10MΩ | 7 | |
| 3 | Testing open circuit resistance is minimal | 5MΩ | / | |
| 4 | The biggest test of insulation resistance | 100 MΩ | / | |
| 5 | The test voltage | 200V | 500 | |
| 6 | Test current biggest | 200 MA | / | |
| inspection | 1 | General inspection items (checks | Can provide the final product inspection report | / |
| View, measuring thickness, size, become warped area, parking aperture) | ||||
| 2 | Thermal stress test | Can provide the thermal stress test report; | / | |
| 3 | The impedance test | Provides the characteristic impedance test report | / | |
| 4 | Withstand voltage test | Can provide the withstand voltage test report; | / | |
| 5 | Ionic contamination test | Can provide the ionic contamination test report; | / | |
| 6 | Solderability test | Can provide the solderability test report; | / | |
| 7 | Metallographic analysis | Can provide the metallographic analysis report; | / | |
| 8 | Insulation resistance test | Can provide the insulation resistance test report; | / | |
| 9 | Peel strength test | Can provide the peel strength test report. | / | |
Copyright ©2009-2015 Shenzhen xinshineng technology development co., ltd. All Rights Reserved.
